Jump to content
Sign in to follow this  

Can't boot SierraAMD v3 after Postinstall

Recommended Posts


I successfully installed macOS Sierra with the Version SierraAMD v3 on my AMD Pc. 

But after setting up the PostInstall via Terminal, the OS stops booting at this line :

ioconsoleusers: gioscreenlockstate 3, hs 0, bs 0, now 0, sm 0x0

Any solutions? 


My System Specs:

Mainboard: Asrock 970 Pro3 r2.0

Processor: AMD FX-6300

Graphics: Sapphire Radeon RX460 4GB



Share this post

Link to post
Share on other sites

Yes thats one of the most annoying errors

it happens to me too when I try to install high Sierra vanilla well there is a fix for it a few fixes maybe this will help.


Fixes! and helpful tips


Mostly this errors occur by gpus if you have a other gpu or a integrated graphics card then try it on that and try to find a answer.

Try to change the fake id in Sierra zone if that works or u probably need some additional kexts to get it work like graphics.


This error occurs when Sierra is installed and you need to set it up mostly but maybe you need to remove the video card and put it back to get it to work ppl say integrated graphics maybe be the fix make sure u have igp enabled (integrated graphics card) and put your sapphire radeon RX460 4GB video card temporarily out of your computer and then try to boot with igpu that should do it I hope it if no luck then i can't do anything about it to.


But also there are findable kernels and kexts for your amd build maybe try to find the right one on this site.


Tip: Sierra zone has already a maded custom kernel for amd fx you only need to boot it with a simple bootflag which I forgot cuz I have intel.

So try to install it fully with Sierra zone without any other things just Sierra zone maybe it helps.



Share this post

Link to post
Share on other sites

Hi, everyone, thanks for your time.
I'm trying to fresh install macOS 10.13.1 (Build 17B48). I'm trying to do this by free myself from multibeast and by put kexts in EFI/CLOVER/kexts/10.3 and set a good config.plist.

I have this famous issue in verbose mode and can't boot.
IOConsoleUsers: time(0) 0->0, lin 0, llk 1,
IOConsoleUsers: gIOScreenLockState 3, hs 0, bs 0, now 0, sm 0x0


It's looks like your own issue.

Every time, i can boot the first time. I start my post-install by install the web drivers automatically served by Nvidia. And never be able to boot again…
I didn't found any plist option that permit to boot over this issue…

help… !

My list of kexts and my config.plist is joined.
Thanks for your time…

Here are my list of used kexts

kexts/10.13 folder :

NvidiaGraphicsFixup.kext    v 1.1.3

AtherosE2200Ethernet.kext    v 1.2.0
FakePCIID_XHCIMux.kext        v 2.2.1
FakePCIID.kext            v 1.3.9
FakeSMC_ACPISensors.kext    v 6.25-333-g05e0f4be.1759
FakeSMC_CPUSensors.kext        v 6.25-333-g05e0f4be.1759
FakeSMC_GPUSensors.kext        v 6.25-333-g05e0f4be.1759
FakeSMC_LPCSensors.kext        v 6.25-333-g05e0f4be.1759
FakeSMC.kext            v 6.25-333-g05e0f4be.1759
HDMIAudio.kext            v 1.0
IntelMausiEthernet.kext        v 2.3.0
Lilu.kext            v 1.2.0
Shiki.kext            v 2.0.5
USBInjectAll.kext        0.6.2

Driver64UEFI folder


Gigabyte GA-Z170X-Gaming 5 | i7-6700(not K) | GTX980ti - OS on SSD.

Share this post

Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community.

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
Sign in to follow this  

  • Create New...